New Product Releases - October 2005

YOKOMO Available 10/29 Water Transfer Carbon Pattern Decal (Water-slide type) ¥780 ZC-CDW Sample of decal applied to a curved surface of a bodyshell. This is a water-transfer type carbon pattern decal. Compared to standard decals, this decal is capable of conforming to curved areas, and provides a nice detailed finish. Decal comes in an A4 size sheet. ●This decal is designed to be used by immersing it in water. ●The flexible characteristic of this decal, allows it to conform to areas that are normally difficult to conform to. ◆Usage Instructions◆ ① Cut out the decal to match the shape of the area being applied. Cutting out the decal slightly larger than the desired shape is not a problem. • A thin, pink-colored protective sheet is provided to allow easier application of the decal. Carefully peel away this sheet once the decal has been correctly positioned. ② Immerse the decal in luke warm water to loosen the decal from the backing paper. ③ Position the decal with the backing paper onto the area to which the decal is to be applied. Slightly move the decal from the backing paper, and position the exposed part of the decal to where it is intended to be applied. Slowly slide the backing paper from underneath, removing it away from the decal. ④ Using a soft dry cloth, or the rounded end of a rubber spatula, gently burnish the surface of the decal to squeeze out any air bubbles or water trapped underneath. • When applying the decal to areas that are difficult to conform to, such as hood scoops, make small cuts in the decal to allow the decal to help conform to the sunken areas. Try not to pull on the decal too tight, as it may cause the decal to tear. • Before the decal is allowed to dry, use a hobby knife to gently cut away any excess portion of the decal. Once the decal has been allowed to dry, removing the decal may be very difficult. ⑤ Once the decal has started to settle into place, slowly remove the protective sheet. (Allow 20-30 minutes for the decal to start settling into place.) Use a dry towel to gently squeeze out any remaining water that may be trapped under the decal. • The protective layer may not be easily visible. Carefully locate an exposed edge, and start peeling from there. ⑥ Leave the decal untouched, and allow adequate time for it to dry. (Leave untouched for at least 2 hours.) • Time required for the decal to dry and settle may vary, depending on the amount of water used to apply it. ● Once dried, additional stickers may be applied to the surface of the decal. • Although stronger that standard water-transfer decals, this decal can be scratched if subjected to crashes or impacts against hard objects.

YOKOMO Available 10/28 GM Power Capacitors (2 pcs) for the V8 V12 SX-9 SX-12 ¥900 GM-1540 Power capacitors included with the SX-12WM. Also compatible with other GM speed controllers. UPC: 639342061822

YOKOMO Available Now MB-4 Custom Carrying Case ¥6,700 M-421040 Custom carrying case (aluminum) for the MB-4. Both the transmitter and car fit neatly into the case for easy transport. Car and transmitter pictured sold separately.

YOKOMO Available Now MB-4 Aluminum Motor Heat Sink ¥350 M-258164 Aluminum motor heat sink for the MB-4. Recommended for use with optional motors or hard usage.

YOKOMO Available Now 7.2V 1100mAh Ni-MH Battery for the MB-4 ¥1,800 M-258175 High-capacity Nickel Metal Hydride battery for the MB-4.

YOKOMO Available Now 32000RPM 380-Type Motor for the MB-4 ¥2,100 M-258218 Optional 32,000RPM motor for the MB-4. High-capacity Nickel Metal Hydride battery and motor heat sink are highly recommended for use with this motor.

YOKOMO Available 10/20 Factory Team Conversion Kit for the RC-10TC4 ¥29,800 FTP-31130 Conversion kit to update the RC-10TC4 Team Kit to Factory Team specs. UPC: 639342061808 For Domestic Sale Only - Not Available For Export

YOKOMO Available 10/14 Upgrade Conversion Stage-3 ¥17,800 SD-GC3 New for Drifting - The awesome look and driving feel of Silver Carbon Graphite! ●The lightweight and stiff SSG chassis allows smoother release of the rear end, and increased drift distances. ●The SSG chassis is allowed for use in the Expert/D1 class at Yokomo Drift Meeting events. Main Features ★SSG Main Chassis ★SSG Upper Deck ★SSG Front Shock Tower ★SSG Rear Shock Tower (New Design) ★SSG Center Stiffener ★Steering Linkage ★Motor Mount Drift Package or Drift Racer required to complete assembly. UPC: 639342060306

YOKOMO Available 10/13 F-0 Metal Bushing Oil ¥1,200 CF-F0O A new metal bushing oil has been added to the popular F-0 series. UPC: 639342061686

YOKOMO Available 10/1 1/18 4WD Mini Buggy MB-4 RTR Set ¥26,000 Introducing the MB-4 1/18th scale 4WD Mini Buggy. The enjoyment of real offroad performance in an affordable package. Factory assembled with electronics. 2 body colors available (purple pictured). MB-4P Purple UPC: 639342061624 MB-4W White UPC: 639342061631 (7.2V600mA Nicd battery and charger included) For Domestic Sale Only - Not Available For Export

YOKOMO Available 10/1 1/18 4WD Mini Buggy MB-4 AAR Set ¥15,500 MB-4AR Introducing the MB-4 1/18th scale 4WD Mini Buggy. This set includes a factory assembled chassis without electronics, and a clear body shell. (7.2V600mA Nicd battery and charging cord included) UPC: 639342061648 For Domestic Sale Only - Not Available For Export

YOKOMO Early October Motor Station ¥5,200 YT-MS Perfect for breaking in motors. Made of machined aluminum. Easily secures motor using a clamp type mechanism. UPC: 639342061655